Product Introduction
Working Principle
Smoke through the welding fume purifier generated by the negative pressure from the suction arm inhalation of dust, through the flexible suction arm into the cavity, the flow rate slows down so that the large particle diameter of the dust falls down, containing fine dust airflow into the purification chamber, dust filtration and separation in the purification chamber through the separation of canisters can be completed by the separation of the role of the smoke is blocked by the filter cartridge on the surface of the purified air through the blower to discharge: when the blocked dust in the surface of the cartridge continues to deposit, regularly open the pulse cleaning system. When the blocked soot is continuously deposited on the surface of the filter element, the pulse cleaning system will be turned on regularly, and the filter cartridge will be taken out and cleaned manually in the manual cleaning type. Electrostatic type needs to clean the electrode plate regularly.
1. Before connecting the power supply, check that the voltage, power supply frequency, and equipment labeling regulations are consistent; 2. Install the grounding wire.
3. Check that the access door is completely in contact with the seal;
4. Check whether the high-efficiency filter cartridge is in tight contact;
5. Check whether the power switch current is consistent with the current used by the motor;
6. The direction of rotation of the motor must be such that the suction hood has a sense of air intake;
7, manipulator tight ready to slide;
8, pull the suction mask, to determine the suction distance angle, so that the suction arm can determine a fixed position; 9, to determine the overall purifier has to run, rotate the power switch, start suction welding fume;
10, the purifier is in working condition, do not open the door;
11. Before starting the purification equipment again, ensure that the purifier fan has completely stopped.
12, in the long-term use of the process must be regularly cleaned up gray mechanical can be directly removed from the filter cartridge with an air compressor from the inside out spray blowing the surface of the gray small thoroughly blown after installation and continue to use, electrostatic need to be pulled out of the discharge plate to clean the surface of the electrode plate after natural drying after installation and continue to use.
Scope of application
This model of welding fume purifier is suitable for manual welding and automatic welding of welding fume, through the suction arm into the body for purification. It is professionally designed for industrial applications.
Smoke through the welding fume purifier generated by the negative pressure from the suction arm inhalation of dust, through the flexible suction arm into the cavity, the flow rate slows down so that the large particle diameter of the dust falls down, containing fine dust airflow into the purification chamber, dust filtration and separation in the purification chamber through the separation of canisters can be completed by the separation of the role of the smoke is blocked by the filter cartridge on the surface of the purified air through the blower to discharge: when the blocked dust in the surface of the cartridge continues to deposit, regularly open the pulse cleaning system. When the blocked soot is continuously deposited on the surface of the filter element, the pulse cleaning system will be turned on regularly, and the filter cartridge will be taken out and cleaned manually in the manual cleaning type. Electrostatic type needs to clean the electrode plate regularly.
1. Before connecting the power supply, check that the voltage, power supply frequency, and equipment labeling regulations are consistent; 2. Install the grounding wire.
3. Check that the access door is completely in contact with the seal;
4. Check whether the high-efficiency filter cartridge is in tight contact;
5. Check whether the power switch current is consistent with the current used by the motor;
6. The direction of rotation of the motor must be such that the suction hood has a sense of air intake;
7, manipulator tight ready to slide;
8, pull the suction mask, to determine the suction distance angle, so that the suction arm can determine a fixed position; 9, to determine the overall purifier has to run, rotate the power switch, start suction welding fume;
10, the purifier is in working condition, do not open the door;
11. Before starting the purification equipment again, ensure that the purifier fan has completely stopped.
12, in the long-term use of the process must be regularly cleaned up gray mechanical can be directly removed from the filter cartridge with an air compressor from the inside out spray blowing the surface of the gray small thoroughly blown after installation and continue to use, electrostatic need to be pulled out of the discharge plate to clean the surface of the electrode plate after natural drying after installation and continue to use.
Scope of application
This model of welding fume purifier is suitable for manual welding and automatic welding of welding fume, through the suction arm into the body for purification. It is professionally designed for industrial applications.